GRAPHTEC CRAFT ROBO CC100 20 DRIVERS FOR MAC DOWNLOAD

Fixed the problem that might not be able to control a cutting plotter from multiple PC when there is a network connection. By pressing ‘print’ button you will print only current page. Fixed the problem that a cut job might be done without refer to the registration mark when it is occured the mark reading error after sending the cut job to the cutting plotter. If you replace the main board, use the following procedure to input the recorded adjustment values. To get the correct force, gently lift the pen up by hand, lower the pen, and then measure the actual force after you click the force button. Fixed the problem that might not be performed the number of times of the specified passes. Glad they got it up!

Uploader: Akirg
Date Added: 9 August 2004
File Size: 57.42 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 70858
Price: Free* [*Free Regsitration Required]

Front guide M3L6 pan head screw Graphtec craft robo cc100-20 In the alternative, does anyone have any information on any other software that I could use to accomplish the same results. Apr 18, 9: In order to be able to post messages on the T-Shirt Forums, you must first register.

GRAPHTEC Craft ROBO CC100-20 Service Manual

Fixed the problem that might not be reflected the setting of Tangential mode to the actual cut of a media even if it is set as “Mode1” or “Mode2” in the cutter condition window. Cradt pan head screw Main board Release here. February 1st, Graphtec craft robo cc100-20 of 42 Go.

To get the correct force, gently lift the pen up by hand, lower the pen, and then measure the actual force after you click the force button. This software is application software for creating original design on the Windows.

Graphtec Craft ROBO CC Manuals

Enter text from picture: December 1st, To print the manual completely, please, download it. Reply With Quote Quick reply to this message. April 18th, Apr 18, 9: I’m not even sure that would be legal for me to if I did. Left side cover Top cover Feed knob Right side cover Added the function to move the tool carriage of default cutter into the same position where the cutting job is moved by dragging on the preview window.

April 21st, Graphtec craft robo cc100-20 21, 8: Fixed a problem that Graphtec Studio shuts down when using the gradient fill function by the configuration of the PC. Do not turn off the standby switch while adjusting the CC Added the display of the total graphtec craft robo cc100-20 of cut jobs on the preview window.

GRAPHTEC Craft ROBO CC100-20 Service Manual

Don’t have an account? Grwphtec board Locking card spacer 10 Release the two locking card spacers holding the main board, and then detach the main board.

Page 36 – Adjusting the Offset of the Auto-Registr If you do so, the CC will not graphtec craft robo cc100-20 any commands from the adjustment yraphtec. Fixed the problem that the cutting plotter might hangs by the condition of the PC during receiving cut data. Drives the cutter pen to the left or right Ball-point pen plunger.

Fixed the problem that might be freezed when a plotfile is output. Need to Upload an Image?

Downloading the Graphtec Studio for Windows OS | GRAPHTEC

July 4th, You won’t be able to post until your email address has been confirmed. Fixed the problem that an error message may be appeared after the reset was executed on the [Weed Setting] or [Tiling panel] graphtec craft robo cc100-20 the stored gstudio file was used.

Go to this site: Fixed the problem that the graphtec craft robo cc100-20 message windows might be appeared when some operation is executed at the Tile panel. Left side cover Top cover Feed knob Please note that it is not possible to download or use the software if the customer does not agree to it. April 21st, Apr 21, 7: Added the function to duplicate the cutting condition in the software.

Twin Cities, MN Posts: